Welcome to Taikyu. Your Spoon Sports Distributor

Recently added item(s) ×

Your Shopping Cart is Empty.

Shopping Options Filter
Product Type
  1. INTAKE
    INTAKE
  2. EXHAUST
    EXHAUST
  3. POWERUNIT
    POWERUNIT
  4. BRAKES
    BRAKES
  5. REINFORCEMENT
    REINFORCEMENT
  6. COOLING
    COOLING
  7. DRIVETRAIN
    DRIVETRAIN
  8. INTERIOR
    INTERIOR
  9. EXTERIOR
    EXTERIOR
  10. SUSPENSION
    SUSPENSION
  11. WHEEL SETS
    WHEEL SETS

Civic FK7

Set Descending Direction

13-24 of 29

Page:
  2. 1
  3. 2
  4. 3
  • FK7 BRAKE PAD [REAR]

    Product Overview

    "

    Spoon brake pads feature high resistance to fading, excellent performance at low temperatures, near stock life expectancy, and low rotor wear

     

    Spoon brake pads provide strong braking power while maintaining stable, consistent, and direct driving feel. This allows drivers to enter corners smoothly. These are suitable for road and track use

    "

    FK7 BRAKE PAD [REAR]

    43022-FK7-S00-A
    Excl. Tax: €208.33 Incl. Tax: €250.00

  • FK7 CARBON BONNET

    Product Overview

    "

    The weight of the SPOON carbon bonnet is 7 kg and 52% lighter than the original bonnet weight of FK 7 14.5 kg.

    The biggest weak point of the tenth generation Civic is the weight of the car, especially the weight reduction of the front section not only alleviates the burden of braking but also the quick turning ability and the good handling characteristics indispensable for sports driving are demonstrated.

    The characteristics of the successive SPOON carbon bonnet keeps the genuine body shape, the design is simple.

    However, the calorific value of the turbo engine adopted from this tenth generation Civic was excessive, and it was necessary to reduce the heat inside the engine room as much as possible. Therefore, the bonnet for FK7 is not only lightweight, but also has an air outlet inside the hood to finish it in a shape that allows the hot air in the engine room peculiar to the turbo engine to escape. By providing an air outlet of the engine room, we will maximize the cooling performance of the radiator and intercooler.

    Remarks & special note

    (Note) Since carbon products may discolor by ultraviolet rays, we recommend that you clear paint for UV protection measures.

    · Be sure to temporarily adjust the product before painting.

    · Since the product will deform under environments such as paint booth / heater, please air dry without adding heat.

    · When the temperature is low such as winter, when the humidity is high etc. Please dry it at 40 ℃ or lower as a whole.

    · Please do not partially heat. It may cause distortion.

    "

    FK7 CARBON BONNET

    60100-FK7-000-C
    Excl. Tax: €1,183.33 Incl. Tax: €1,420.00

  • FK7 CARBON ROOF SPOILER

    Product Overview

    "

    We improved the stability in the high speed range by finishing the design that made use of the characteristic roof line and beautiful body form of the new Civic hatchback and maximizing the rectifying effect. WING part is carbon specification. The mount part is FRP white gel finish.

    Remarks & special note

    (Attention)

    · Since the mount part is white gel coat finish, painting is necessary.

    · Since carbon products may discolor by ultraviolet rays, we recommend that you clear paint for UV protection measures.

    Be sure to temporarily adjust the product before painting.

    · Since the product will deform under environments such as paint booth / heater, please air dry without adding heat.

    · When the temperature is low such as winter, when the humidity is high etc. Please dry it at 40 ℃ or lower as a whole.

    · Please do not partially heat. It may cause distortion.

    "

    FK7 CARBON ROOF SPOILER

    68800-FK7-020-C
    Excl. Tax: €1,075.00 Incl. Tax: €1,290.00

  • FK7 FRP ROOF SPOILER

    Product Overview

    We improved the stability in the high speed range by finishing the design that made use of the characteristic roof line and beautiful body form of the new Civic hatchback and maximizing the rectifying effect. WING part is carbon specification. The mount part is FRP white gel finish.

    Remarks & special note

    (Attention)

    · Since the mount part is white gel coat finish, painting is necessary.

    Be sure to temporarily adjust the product before painting.

    · Since the product will deform under environments such as paint booth / heater, please air dry without adding heat.

    · When the temperature is low such as winter, when the humidity is high etc. Please dry it at 40 ℃ or lower as a whole.

    · Please do not partially heat. It may cause distortion.

    "

    FK7 FRP ROOF SPOILER

    68800-FK7-000-C
    Excl. Tax: €620.83 Incl. Tax: €745.00

  • FK7 HEAD COVER [RED]

    Product Overview

    Although the genuine head cover of the tenth generation Civic is made of resin, We applied a red crystal paint which can be said as a symbol of TYPE R by a special method and SPOON yellow paint which has been inherited from the successive Civic. 


    In the STD state, you can casually modify the engine bay

    FK7 HEAD COVER [RED]

    12310-FK7-R00-C
    Excl. Tax: €366.67 Incl. Tax: €440.00

  • FK7 HEAD COVER [YELLOW]

    Product Overview

    Although the genuine head cover of the tenth generation Civic is made of resin, We applied a red crystal paint which can be said as a symbol of TYPE R by a special method and SPOON yellow paint which has been inherited from the successive Civic. 


    In the STD state, you can casually modify the engine bay

    FK7 HEAD COVER [YELLOW]

    12310-FK7-Y00-C
    Excl. Tax: €366.67 Incl. Tax: €440.00

  • FK7 LOW TEMP THERMOSTAT

    Product Overview

    "

    The Spoon Thermostat benefits from a reduced operating temperature trigger to allow it to commence opening at a lower temperature and then reach full open at an again reduced temperature.

    Starts opening at 68 degrees vs oem of 80 degress, fully open at 80 degrees vs oem of 90 degrees/p>"

    FK7 LOW TEMP THERMOSTAT

    19301-FK7-000-A
    Excl. Tax: €70.83 Incl. Tax: €85.00

  • FK7 N1 MUFFLER KIT

    Product Overview

    The L15C mounted on the new Civic 1.5 Turbo demonstrates 182 PS while 1.5 L but it is characteristic of thick torque from low to medium speed, but in SPOON, in order to further improve its high torque and high response, development of an exhaust system Has been promoted.

     

    The main pipe uses SUS304 material Φ60, and the tail adopts Φ65 finisher for Φ127 shell type dual silencer. Both high-quality N1 sound and exhaust efficiency improvement were compatible.

     

    As with CIVIC TYPE R (FK 8), it is also essential to increase the diameter of the front pipe to pursue even higher output and high torque with ECU tune such as boost up. We also developed a front pipe with a pipe diameter of 60 Φ.

     

    It is JQR certified and compliant with safety standards.

    Proximity Exhaust Noise: 92 db 
    Acceleration Running Noise: 74 db

    FK7 N1 MUFFLER KIT

    18000-FK7-000-A
    Excl. Tax: €1,908.33 Incl. Tax: €2,290.00

  • FK7 PROGRESSIVE LOWERING SPRINGS

    Product Overview

    "

    Spoon progressive springs are designed to provide optimal ride height and camber, while working in conjunction with the stock dampers or the uprated Spoon fixed dampers.

    The progressive spring lowers the vehicle ride height reducing the amount of roll, increasing manoeuvrability and stability without compromise to ride quality. Comfortable ride at city driving speeds and stiffer, more responsive handling at higher demands.

    Progressive springs are recommended for enthusiasts wanting a sportier driving feel without the cost and harshness of dedicated track coilovers.

     

    Remarks & Notice

    Spring rate FRONT: 2.7kg / mm REAR: 3.2kg / mm - ride height lowering: 30mm

    "

    FK7 PROGRESSIVE LOWERING SPRINGS

    51400-FK7-001-A
    Excl. Tax: €395.83 Incl. Tax: €475.00

  • Limited Edition - Spoon Bobblehead

    Product Overview

    PREODER:

     

    Spoon Sports Japan Limited Edition 30th Anniversary Spoon Bobblehead in unquire cool packaging. A True Collectable ! Japan are making these is a very limited production run for the Tokyo Auto Salon but we have reserved some for out loyal EU customers.

     

    Place an order now so you are not dissapointed.

     

    Orders will ship mid-late February

    Limited Edition - Spoon Bobblehead

    ORG-90004-000-B
    Excl. Tax: €36.67 Incl. Tax: €44.00

  • Limited Edition - Spoon Kanpachi Cap

    Product Overview

    NOT AVAILABLE

     

    Spoon Sports Japan Limited Edition 30th Anniversary Kanpachi Cap. Japan are making these is a very limited production run for the Tokyo Auto Salon but we have reserved some for out loyal EU customers.

     

    Place an order now so you are not dissapointed.

     

    Orders will ship mid-late February

    Limited Edition - Spoon Kanpachi Cap

    ORG-APR03-000-B
    Excl. Tax: €34.17 Incl. Tax: €41.00

  • MOTION CONTROL BEAM KIT FOR FK7/8 & FC1

    Product Overview

    The ideal body structure proposed by SPOON is “rigidization”. 

    The newly developed `` Motion Control Beam '' has a special structure for controlling the rigidity of the front and rear ends of the body where the torsion is most likely to occur. This product improves comfort and quality. 

    Since the 90s, Spoon has participated in touring car races based on commercial vehicles, and demonstrates how the technology, knowledge and experience gained from the race can be demonstrated without compromising the comfort and quality required for street use. We have been working on product development based on the theme. 

    Among SPOON's body parts born from the feedback from the race site, the most representative product is “Rigidkara” released in 2007. With Rigidkara, the monocoque and sub-frame are made rigid by filling the gap between the body, sub-frame, and fastening bolt with a specially shaped collar and tightening firmly. 

    This time, we focused on “torsion control of the end of the body” that occurs during cornering and “compatibility of comfort and high quality necessary for street use”. 

    "Motion control beam" is fastened with a damper equipped with a special friction mechanism at the forefront of the front reinforcement and the rear end of the rear end panel. 

    By installing a friction damper against the twist on the body side diagonal due to load movement, we succeeded in significantly reducing the torsion of the body while ensuring a certain level of rigidity. 

    Although the normal reinforcement brace alone can secure rigidity, the fine vibration will increase. However, by installing this friction damper, the fine vibration is absorbed and a high-quality ride with no noise is realized. 

    "Motion control beam" is a simple structure with high resilience spring and friction plate.

    A large input works against the torsion of the body that occurs during cornering, and the high repulsion spring suppresses the torsion in the same way as the brace. 

    On the other hand, a small input suppresses twisting finely by the elastic force of the friction plate. 

    By controlling this non-constant torsional input separately, it is possible to perform a wide range of suppression.
    ---
    Remarks & Special notes
    Spoon focuses on 

    “rigidization” that raises the basic performance of the car> “Rigidkara” is a product that brings out the dynamic performance of the vehicle, but “Motion Control Beam” controls the twist of the body end. However, it is a product developed from a different point of view that reduces the uncomfortable feeling of line traceability and vibration as desired. 

    The simultaneous mounting allows you to reproduce a high-quality ride without further nuisance. 

    Installation instructions 
    https://www.spoonsports.jp/blog/wp-content/uploads/2019/08/50500-FKA-000.pdf

    MOTION CONTROL BEAM KIT FOR FK7/8 & FC1

    50500-FKA-000-D
    Excl. Tax: €937.50 Incl. Tax: €1,125.00

Set Descending Direction

13-24 of 29

Page:
  2. 1
  3. 2
  4. 3

Shipping Information

Information on Stock Availability & Delivery

 

Stock item, next day delivery
Less than 5 stocked, next day delivery
Stock level usually 1, delivery could be delayed
Not a usual stock item, delivery time will vary.
Special Order Item, 4 to 6 Weeks Delivery.

 

Estimated stock and delivery time Only!

As we have multiple sales avenues we cannot guarantee product stock status. Any questions click the Chat button and someone will assist you.

Product Enquiry

Instagram

    Contact us

    Taikyu Ltd

    Unit C Mendip Business Park

    Rooksbridge, Somerset

    BS26 2UG

    England, UK

    +44 (0) 33 022 33 486
     info@taikyu.uk
    <

    Loading, please wait ... Loading, please wait ...