Welcome to Taikyu. Your Spoon Sports Distributor

S2000 AP1 / AP2

  • AP1_890
    S2000 - AP1 / AP2

Set Descending Direction

49-60 of 127

  • DIFFERENTIAL MOUNT SET

    Product Overview

    The S2000 has a few weak points, and one of these is a weak differential mount.

     

    By controlling the position of the differential during power-on and in tailskid situations, it is possible to achieve high stiffness in the rear end, resulting in tight cornering and forward driving which is both stable and solid.

    DIFFERENTIAL MOUNT SET

    50700-AP1-001-A
    Excl. Tax: €383.33 Incl. Tax: €460.00

  • DRIVE SHAFT BOOT SET

    Product Overview

    On the left is the Spoon Drive Shaft Boot Set, and on the right is the standard Shaft Boot Set.

    DRIVE SHAFT BOOT SET

    42010-AP1-000-A
    Excl. Tax: €279.17 Incl. Tax: €335.00

  • DRIVE SHAFT SPACER KIT

    Product Overview

    The importance of a reliable driveshaft is often overlooked in endurance racing to street applications. The standard Honda units do not lack strength themselves, the troubles and failure of the driveshafts are often the finishing quality. Slight pitting can occur on the contact surfaces, which under high heat deteriorate which then cause vibrations and failure.

     

    The Spoon drive shafts are standard Honda units that have been disassembled then reworked and reassembled by Spoon technicians. Each contact surface has been polished and finished to exacting standards and then the components are matched during assembly to ensure the highest tolerances.

     

    This ensures a smooth power delivery and reliable service 

    DRIVE SHAFT SPACER KIT

    42320-AP1-000-A
    Excl. Tax: €200.00 Incl. Tax: €240.00

  • ENGINE MOUNT RING

    Product Overview

    The Spoon engine mount ring is used to reduce the deflection angle of the engine.  This results in a much stiffer connection between the engine and the chassis preventing unwanted engine vibration.

     

    Notice:

    When used in connection with the Spoon Up rated engine mount such stiffness can occur that un even engine idle can cause a vibration noise. 

    ENGINE MOUNT RING

    50816-AP1-000-A
    Excl. Tax: €145.83 Incl. Tax: €175.00

  • ENGINE TRANSMISSION MOUNT SET

    Product Overview

    With the Spoon engine and transmission mounts the rubber hardness is increased from 55-75 (Shore D) and the effective spring rate of the bush is increased from 6kgf/mm to 14kgf/mm

    Additionally Spoon also reinforced the transmission bush mount bar

    It is recommended that you seek if a further hardening, also use the engine mount ring.

    ENGINE TRANSMISSION MOUNT SET

    50800-AP1-010-A
    Excl. Tax: €416.67 Incl. Tax: €500.00

  • EXHAUST MANIFOLD [4-2-1]

    Product Overview

    The Spoon 4-2-1 header is designed to provide the maximum balance between peak power and torque.

    To develop this header, Spoon tested all possible combinations of pipe diameter, length, bends, and rotation through engine dyno, flow bench, and driving/circuit tests. The result was an extremely lightweight header (5.2kg) with substantial peak and mid-range power gains. Weight saving 50% over the OEM manifold of 10.2kg

    For best results we recommend installing the with Spoon N1 Muffler kit. 

    Notice: Unlike many of the Spoon Sports exhaust products. This does not have a the Spoon Sports badge installed. 

    EXHAUST MANIFOLD [4-2-1]

    18101-AP1-000-D
    Excl. Tax: €1,087.50 Incl. Tax: €1,305.00

  • F20C 2.2L STROKER KIT

    Product Overview

    The Spoon F20C Stroker has been designed to allow the standard Honda F20C be over stroked to the 2.2L capacity. Unleashing torque that some have complained the S2000 was missing in the past and increasing power.

    The kit comprises of: Head gasket, crankshaft, connecting rods, forged pistons, rings, pins, oil jet. All parts are selected and balanced within .2g with a total rotational tolerance of less than 1g

    Kit supplied with 0.25mm over bore pistons and rings

    Higher compression will be achieved 11.8:1 (STD 11.7:1) Inner diameter × stroke (mm): 87.25 × 90.7

    F20C 2.2L STROKER KIT

    13000-F22-000-B
    Excl. Tax: €2,625.00 Incl. Tax: €3,150.00

  • FENDER [REAR]

    Product Overview

    Fits all S2000 model years. FRP Construction. Widens rear end by 25mm.

     

    Finished in white and ready to paint 

    FENDER [REAR]

    63000-AP1-000-B
    Excl. Tax: €662.50 Incl. Tax: €795.00

  • FINAL GEAR SET (4.4)

    Product Overview

    Spoon Sports final drive ratio gives and overall reduction in all gearing. This allows for improved acceleration and achievable top speed. An excellent modification to allow for a better use of engine power.

     

    Remarks

    4.44 (4.1 STD)

    FINAL GEAR SET (4.4)

    41220-AP1-000-C
    Excl. Tax: €895.83 Incl. Tax: €1,075.00

  • HEAD COVER [YELLOW]

    Product Overview

    The signature Spoon Yellow head cover is now available to all Spoon Fans. For years the yellow head cover was reserved for the Spoon Race cars. However after many requests from customers, Spoon decided to release it. 

    HEAD COVER [YELLOW]

    12310-AP1-000-C
    Excl. Tax: €458.33 Incl. Tax: €550.00

  • HEAD COVER [YELLOW]

    Product Overview

    The signature Spoon Yellow head cover is now available to all Spoon Fans. For years the yellow head cover was reserved for the Spoon Race cars. However after many requests from customers, Spoon decided to release it. 

    HEAD COVER [YELLOW]

    12310-AP2-000-C
    Excl. Tax: €458.33 Incl. Tax: €550.00

  • HIGH FLOW AIR FILTER

    Product Overview

    New version features a multilayer urethane material instead of the OEM high density paper material. The use of urethane dramatically improves filter efficiency. This filter cannot be washed and re-used. Replace with normal recommended factory intervals.

    Upon full opening of the throttle, a huge volume of air is drawn in at highspeeds. Meanwhile, when the throttle is closed, an inertial force acts and air is compressed at the instant just prior to full closing. When the accelerator is subsequently depressed, the sealed cleaner box is subjected to a more intense vacuum as a result of the reaction to compression. The efficiency of replenishment is increased a result of this action, and accordingly, the air-intake system of the Honda NA is both extremely ingenious and highly necessary.

    HIGH FLOW AIR FILTER

    17220-AP1-010-A
    Excl. Tax: €93.33 Incl. Tax: €112.00

Set Descending Direction

49-60 of 127

Shipping Information

Information on Stock Availability & Delivery


 

Stock item, next day delivery
Less than 5 stocked, next day delivery
Stock level usually 1, delivery could be delayed
Not a usual stock item, delivery time will vary.
Special Order Item, 4 to 6 Weeks Delivery.

 

Estimated stock and delivery time Only!

As we have multiple sales avenues we cannot guarantee product stock status. Any questions click the Chat button and someone will assist you.

Product Enquiry

<

Loading, please wait ... Loading, please wait ...